THERMADOR Error Code F3 – How to fix? by ApplianceRepairNewYork.us
THERMADOR Error Code F3
Professional Ranges Models: PDR30/36/48…PRG30/36/48
| ERROR CODE | DESCRIPTION | RESOLUTION |
| CODE F3 | Open circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor | Replace sensor if other components check normal. Repair electronic range control (also called clock or ERC) if fail code reoccurs |
The control continually monitors system criteria for control and oven failures and also reports a fault code when a system problem is found. The control makes use of the ovens blue “on light” and oven “home heating light” to report a discovered mistake code. The control will certainly continue to blink the lights in the appropriate series as long as the fault exists.
Detection of a mistake does not prevent the capability of the control to remain to operate if the fault is not essential for the desired procedure. For example: If the variety door lock is defective, the array will certainly remain to cook because the mistake would just stop the variety from self-cleaning.
HOW TO INTERPRET CODES
When a fault occurs, the control will certainly flash the blue oven “on light” and the Blue “heating light” sequentially to indicate the mistake. The fault codes have 2 numbers, these numbers are analyzed by the number of times the lights blink. The stove “on light” will flash suggesting the very first number, as well as the “heating light” will blink indicating the second number.
EXAMPLE:
Mistake E9 is … No Air conditioning Followers. The code is 43. The oven “on light” will certainly flash four times, then the “home heating light” will certainly flash 3 times, after that pause. The sequence will certainly then repeat as long as the fault exists.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The following graph shows the error codes that can be displayed in the Oven/Selector home window throughout particular oven breakdowns. Several of the mistake messages can be gotten rid of by doing the following steps:
- Transform the selector handle to OFF
2.”Fine-tune” the oven by turning the selector handle somewhat to the left (counterclockwise). This might stop the flashing message/beeping and also clear the home window. - For errors E1, E9, E11, E12 and also E13, the power supply mosting likely to the also need to be switched off for a little while, and also back on once more.
- If a mistake remains displayed when the selector switch is OFF, and after attempting to get rid of the display screen, as shown in actions 2 and also 3, shut off the power mosting likely to the stove, and refer to the chart listed below to help you locate the problem.
| ERROR CODE | NOTE | CHECK REPAIR |
| F0 | Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode | Replace the electronic range control (also called clock or ERC) |
| F1 | Internal logic failure (monitoring function). Sounds alarm and inhibits cook modes | Replace the electronic range control (also called clock or ERC) |
| F2 | Temperature runaway detected (Bake/Broil: 600 – 700 F; Clean: 930 – 1000 degrees F). Sounds alarm and resets to non-cook mode. Check relay board for stuck contacts. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check sensor wiring connectors for a loose or high resistance connection. Check electronic range control (also called clock or ERC) functions | Replace relay board if necessary. Replace oven temperature sensor if other components check normal. If failure repeats, replace electronic range control (also called clock or ERC) |
| F3 | Open circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor | Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs |
| F4 | Short circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires between electronic range control (also called clock or ERC) and sensor. | Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs |
| F7 | Function key shorted for over 16 seconds. Check for something pressing a key or preventing normal release of the key | Replace electronic range control (also called clock or ERC) if other components check normal |
| F8 | Internal logic failure; calibration. Alarm sounds and resets to non-cook mode. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor | Replace electronic range control (also called clock or ERC) and oven temperature sensor if other components check normal |
| F9 | Internal logic ailure; door latch supervision. Alarm sounds and resets to non-cook mode. If door is locked due to clean temperatures, disconnect power until door can be unlocked | Replace the electronic range control (also called clock or ERC) |
| Fd | Bake & Broil relay drives active simultaneously. Check relay board for damage: trace E6 to K2 & K3, and burned contacts K3 & K3 | Replace electronic range control (also called clock or ERC). Replace relay board if necessary |
| Blank Display | No power to lectronic range control (also called clock or ERC). Check oven light and cooktop dial lights (powered by L2 & L1, respectively). Check relay board transformer primary, E1 to E2 (140 ohms typical). If the transformer internal fuse is still OK, check output voltages, pins 9 – 8 (3.2 v.a.c.) and 7 – 6 (21 v.a.c.). Check clock functions after replacing relay board | If relay board transformer open (E1 to E2), replace relay board. If still no clock functions replace electronic range control (also called clock or ERC) |
| ERROR CODE | NOTES |
| A | Turns heat off on the failed oven only; microwave not affected. |
| B | Turns all heat off; microwave not affected. |
| C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
| D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
| E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
| F | Tweaking clears to “—“ for retry. |
| G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
| H | Can be cancelled by tweaking if a good sensor is detected. |
| I | Cleared with a mode change. |
| J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
| K | Turns heat and microwave off. |
| L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |